What should i use to repair plaster in a bathroom?

Otilia Conn asked a question: What should i use to repair plaster in a bathroom?
Asked By: Otilia Conn
Date created: Sun, Jun 6, 2021 3:00 AM

Content

FAQ

Those who are looking for an answer to the question «What should i use to repair plaster in a bathroom?» often ask the following questions:

❔ How to repair plaster bathroom walls?

This Old House general contractor Tom Silva shows a newer, faster way to fix cracked, loose plaster walls. (See below for a shopping list and tools.)SUBSCRIB...

❔ How do you repair plaster walls in a bathroom?

  1. Step 1: Remove Damaged Plaster. Remove the damaged plaster by using a cold chisel and a ball peen hammer to chip the damaged plaster off the wall…
  2. Step 2: Apply Latex Bonding Agent…
  3. Step 3: Apply and Cross-Scratch Plaster…
  4. Step 4: Apply Second Layer…
  5. Step 5: Apply layer of Joint Compound.

❔ What plaster to use in bathroom?

For plaster use PVA or a PVA slurry if it’s bad but for tiles use an acrylic bonding primer or SBR slurry; do not use PVA. Brad77 said: ↑ The other wall with the loose plaster, looks like I need to chip all of it off, luckily this is the wall with the door and end of the bath, so its not too big.

9 other answers

There are a few options that can be used to repair this damage. You can use standard joint compound (non-lightweight), and apply it in thin coats to avoid cracking due to shrinking, joint compound mixed with plaster, or professional grade oil based drywall spackle. The first step would be to dry the wall and inspect it for mold.

Next, you must remove the peeling and damaged sections of plaster from your bathroom wall. Use a drywall knife or other scraping tool to gently scrape away any peeling or soft sections of plaster...

Finishing Skim is a more watery type of filler that you apply with a paintbrush, then smooth over with the scraper that is supplied in the tub. I applied the skim quite liberally in all directions with the paintbrush as I found that this had the best outcome.

Gently use a scraper but avoid scoring through the surface into the plaster. Apply warm water or proprietary wallpaper stripper with a sponge or brush. Use a steam stripper to remove stubborn coatings, being careful not to allow steam to penetrate the plaster. Treating damp and staining

First remove any loose chunks of plaster use a hammer and chisel if necessary then vacuum out the area to get rid of the dust and debris. 11. Brush in a PVA mix to give the plaster the best possible chance of bonding with the existing wall. 12. Mix up plaster according to the manufacturer’s instructions.

Smooth Damaged Areas With a Scraper The first step is to prep the area by removing any loose or flaking plaster. Use a cold chisel and and ball pein hammer to chip away the damaged plaster and us a scraper to scrape away excess debris. Take care not to hit too hard with the hammer as it could damage the wood lath behind the plaster.

For plaster use PVA or a PVA slurry if it’s bad but for tiles use an acrylic bonding primer or SBR slurry; do not use PVA. Brad77 said: ↑ The other wall with the loose plaster, looks like I need to chip all of it off, luckily this is the wall with the door and end of the bath, so its not too big.

This Old House general contractor Tom Silva shows a newer, faster way to fix cracked, loose plaster walls. (See below for a shopping list and tools.)SUBSCRIB...

Leah demonstrates how to repair a hole in a plaster wall or ceiling with drywall, using a method where she sisters the studs and shims the drywall to fit flu...

Your Answer

We've handpicked 23 related questions for you, similar to «What should i use to repair plaster in a bathroom?» so you can surely find the answer!

How to plaster a bathroom wall?

The premixed clay mortar must be mixed with water. Then let the plaster mass “sump” for a short time. Begin by applying the plaster on top of the wall. Using a flat trowel, first apply a 2-3 mm thick layer of clay.

Read more

Can i plaster over tiles in bathroom?

If you must dry line, your best bet is to fit studs over the tiles then screw plasterboard over this, skim and decorate. If the tiles are well adhered and flat you may be better off gluing the board up with pinkgrip or similar, it will have the same effect as dot and dab but with far more mechanical grab.

Read more

Can you plaster over tiles bathroom backsplash?

You've done every thing *** about face. Should have removed the old suit, striped the tiles, got it plastered, fit the new suite then decorate. I'd be surprised if there were any plasterers happy to plaster over tiles. If you must dry line, your best bet is to fit studs over the tiles then screw plasterboard over this, skim and decorate.

Read more

Can you plaster over tiles bathroom countertops?

You've done every thing *** about face. Should have removed the old suit, striped the tiles, got it plastered, fit the new suite then decorate. I'd be surprised if there were any plasterers happy to plaster over tiles. If you must dry line, your best bet is to fit studs over the tiles then screw plasterboard over this, skim and decorate.

Read more

Can you plaster over tiles bathroom ideas?

I have seen a few questions about putting plasterboard over existing tiles. None of the answers were that conclusive and someone out there might find this useful as I needed to do this myself in a bathroom. The existing tiles and the wall they were on was very sound and so I simply used the screwfix adhesive (Pinkgrip) in lines down and across the ...

Read more

Can you plaster over tiles bathroom tile?

can you tile over old tiles with ceramic tiles and the old fashioned sticky type tiles as they are hard to get up in some places. Bathroom floor tiles - grout between tiles cracked and chunks sinking, tiles lifting. I had a new bathroom completed just over a year ago. It was a local bathroom shop that did the complete bathroom refit and it was...

Read more

Can you plaster over tiles bathroom walls?

Country: i've replastered a bathroom over existing tiles that were stuck on ok but looked dreadful. 1st apply thistle bonding coat very thinly (aim 1mm or so scratch coat). the bits in the bonding mean it won't be smooth). 2nd i put thistle browning coat very thinly on top (1mm or so scratch coat). this was just to make sure all the areas were ...

Read more

Do you have to plaster bathroom ceiling?

2 Answers from MyBuilder Plasterers

While not essential that it was plastered, it is preferable. What you now have is a very porous surface (especially the dry-lining filler used in the joints) i never advocate the use of pva on any surface that is to be painted and consider advice to do so bad advice.

Read more

How much to plaster a bathroom ceiling?

Plastering a ceiling can improve the appearance of any room, with costs starting at £200 for a small ceiling. Skimming your ceiling is an effective way to remove lumps …

Read more

How to install wall tile bathroom plaster?

Firstly check the condition of the plaster skim, it should be fully dried out and a light pink colour. You must also check that the plaster does not have a shine on it, this is caused by over trowelling the plaster when applied, if it has then a wire brush is needed to roughen up the surface.

Read more

How to paint new plaster bathroom ceiling?

Water down the paint for the new plaster. Pour one part of the paint in a bucket/kettle and mix it with clean, cold water. In the case of standard mid-thick paint, the following formula should work well: Mist coat mix = 20% water : 80% paint. Next, thoroughly stir

Read more

How to paint new plaster in bathroom?

Painting new plaster that’s completely dry can also leave you with uneven brush strokes. So, the next course of action is to create your own mist coat paint. Mist coat paint is simply watered-down emulsion paint, which acts as your primer. All you need to do is get some white emulsion paint and thin it out with water – it’s that easy! Three parts paint to one part water should work.

Read more

How to paint plaster walls in bathroom?

I would let the plaster dry as much as you can, keep a small window open now it has gone off. Don't just paint it cos it's there. I would use a water based eggshell. It gives a low sheen surface with excellent water/damp repelling properties. Thin the first coat (with water, approx 10-15%) apply by fine hair roller and add 2 subsequent coats.

Read more

How to remove section of plaster bathroom?

How to Remove Wire Lath/Wire Mesh Plaster Tile Walls Bathroom Demolition - YouTube.

Read more

How to seal plaster walls in bathroom?

Steps 1 Prepare the sealer. First, put on your respirator mask because sealer fumes can be quite potent. Remove the can lid... 2 Cut in the edges. Before you start sealing the walls with your roller, cut in the edges using a paintbrush. Cutting in... 3 Seal the wall. Now, pour the sealer into your ...

Read more

Why is plaster in bathroom feel gritty?

140235. try using a relatively clean bucket and also make sure its clean water your using, make sure paddle mixer is clean and free of any flaking plaster remnants, check the plaster is in date and also its not a damp and an open bag thats a few weeks old that airs got to.. Pva the ceiling 3:1 mix to seal the ceiling let it dry 15-20 mins then Pva ...

Read more

How much to paint and plaster a bathroom a bathroom?

NEW Edit, Print & Save this in Homewyse Lists Create your own price list in Homewyse Lists For a basic project in zip code 47474 with 120 square feet, the cost to Paint a Bathroom starts at $3.19 - $6.61 per square foot. Actual costs will depend on job size, conditions, and options.

Read more

Can you use bathroom paint on new plaster?

Painting new plaster that’s completely dry can also leave you with uneven brush strokes. So, the next course of action is to create your own mist coat paint. Mist coat paint is simply watered-down emulsion paint, which acts as your primer. All you need to do is get some white emulsion paint and thin it out with water – it’s that easy!

Read more

Do i need to remove plaster in bathroom?

You need to remove all plaster that is moisture damaged. By the time that is done, it is well beyond a spackle patch job, it requires re-plastering. Dry mix would work of course, though I would expect that pre-mixed patching plaster would be available in most areas.

Read more

Do you have to plaster a bathroom wall?

  • Sometimes, you may want to plaster bathroom walls over existing tiles. In this case, you need to fill the gaps between the tiles to create a uniform, flat surface. To do this, you should cover the tiled wall with a non-shrinking, adherent substrate plaster. Apply your chosen plaster finish

Read more

How to paint on fresh plaster in bathroom?

I would let the plaster dry as much as you can, keep a small window open now it has gone off. Don't just paint it cos it's there. I would use a water based eggshell. It gives a low sheen surface with excellent water/damp repelling properties. Thin the first coat (with water, approx 10-15%) apply by fine hair roller and add 2 subsequent coats.

Read more

How to remove bathroom tile from plaster walls?

First, slide your putty knife beneath one edge of the tile, easing it in as far as you can. Repeat the process around all four sides of the tile to loosen it uniformly. Use your putty knife as a lever, bringing the handle closer to the wall. This will help pry the tile away from the plaster gently but effectively.

Read more

Should i caulk around bathroom sink faucet repair?

Besides, do you caulk around bathroom faucet? Yes, you need to caulk around your bathtub's faucet. The caulking will keep any water and other liquids from going behind the faucet and into the wall behind the bathtub/shower assembly. Is plumber's putty necessary for bathroom faucet? 6 Answers. Increasingly, I'm finding that plumber's putty is not recommended for sink drains, especially if it has its own rubber gasket.

Read more